ホーム > 製品情報 > シームレス鋼管 > 高圧ボイラ用マルチリプルシームレス鋼管

高圧ボイラ用マルチリプルシームレス鋼管

お支払い方法の種類:
L/C,T/T,D/P,Paypal,Money Gram,Western Union
インコタームズ:
FOB,CFR,CIF,FCA,CPT
最小注文数:
0.5 Ton
輸送方法:
Ocean,Land,Air
ポート:
Shanghai,Ningbo
  • 製品の説明
Overview
製品の属性

モデルGB/T 20409

ブランドトーリック

供給能力と追加情報

包装束の中の木箱

生産高60000 Tons per Year

輸送方法Ocean,Land,Air

原産地中国

についてのサポート60000 Tons per Year

認証 ISO 9001 ISO 14001 TS 16949 EN 10204.3.1 LR KR

HSコード7304311000

ポートShanghai,Ningbo

お支払い方法の種類L/C,T/T,D/P,Paypal,Money Gram,Western Union

インコタームズFOB,CFR,CIF,FCA,CPT

梱包と配送
販売単位:
Ton
パッケージ型式:
束の中の木箱

高圧ボイラ用マルチリプルシームレス鋼管


用途 :高品質の炭素構造鋼、合金構造鋼の冷間引抜きまたは高圧および高圧力の製造に適したボイラー用の冷間圧延雌ねじ管 \

サイズ :長さ - 8-12m
OD - 28.6-66.7mm
WT - 6.38-18.33mm
曲率 - ≤1.0mm/ m

表面品質:
1.雌ねじ付きチューブの内面および外面には、ひび割れ、折れ曲がり、結び目、折り目、および剥離がありません。これらの欠陥は完全に除去されるべきである。欠陥除去の深さは壁厚の10%を超えてはならず、充填除去部位における実際の壁厚は壁厚より小さくしてはならない。許容される最小の厚さの偏差、クリアランスは四捨五入する必要があります
2.糸の形を損なわないでください。引抜き、カール、崩壊がないこと。
3.雌ねじ付きチューブの内外の直線状の表面(尖っていないコアロッドを含む)は、最小肉厚の4%以下、最大0.2 mmの深さを持たせなければならない。
4.壁の厚さを超えて負の偏差を許容しない他の局所的不完全さが存在すること。
5.薄い酸化物層が検査を妨げないように、雌ねじ付き管の内面および外面の酸化スケールを除去する必要があります。


鋼の等級および化学組成

Number Brand chemical composition(mass fraction)/ %
C Mn Si Cr Mo S P
1 20G 0.17~0.23 0.35~0.65 0.17~0.37 -- -- ≤0.020 ≤0.025
2 20MnG 0.17~0.23 0.70~1.00 0.17~0.37 -- -- ≤0.020 ≤0.025
3 25MnG 0.22~0.29 0.7~1.00 0.17~0.37 -- -- ≤0.020 ≤0.025
4 12CrMoG 0.08~0.15 0.40~0.70 0.17~0.37 0.40~0.70 0.40~0.55 ≤0.020 ≤0.025
5 15CrMoG 0.12~0.18 0.40~0.70 0.17~0.37 0.80~1.10 0.40~0.55 ≤0.020 ≤0.025

Note1:Residual element content of 20G,20MnG,25MnG should satisfy: Cu≤0.20%,Cr≤0.25%,Ni≤0.25%,V≤0.08%,Mo≤0.15%;The remaining elements of other brands should satisfy: Cu≤0.20%,Ni≤0.30%.
Note2:The acid soluble aluminum in 20G steel should not be more than 0.010%.
Note3:The nitrogen content of the steel produced by the oxygen converter plus the refining of the furnace should not be more than 0.008%.


内部スクリュー管のサイズおよびねじパラメータの許容偏差

Code Project [A" teeth types allowable deviation [B" teeth types allowable deviation
A

O.D≤38.1mm
38.1mm<O.D<50.8mm
50.8mm≤O.D≤63.5mm
O.D≥63.5mm

±0.15mm
±0.20mm
±0.25mm
±0.30mm

--
B

O.D≤38.1mm
38.1mm<O.D<50.8mm
50.8mm≤O.D≤63.5mm
O.D≥63.5mm

--

±0.15mm
±0.20mm
±0.25mm
±0.30mm

C

I.D of the root of the screw Thread:
O.D-(1.11×Minimum W.T×2)
O.D≤38.1mm
38.1mm<O.D<50.8mm
50.8mm≤O.D≤63.5mm
O.D≥63.5mm

±0.15mm
±0.20mm
±0.25mm
±0.30mm

±0.15mm
±0.20mm
±0.25mm
±0.30mm

E Minimum I.D Negative deviation to zero Negative deviation to zero
F Minimum W.T

+22%
0

+22%
0

G Thread tips -- --
I Thread top width -- --

Height of thread:
O.D≤38.1mm
38.1mm<O.D<50.8mm
50.8mm≤O.D≤63.5mm
O.D≥63.5mm

±0.3mm

±0.18mm
±0.20mm
±0.23mm
±0.28mm

K Side Angle of thread. ±15° ±15°
O radius of rounded corner at the root of thread -- --
M Thread pitch ±3.2mm ±3.2mm
N Thread lead ±3.2mm×thread tips ±3.2mm×thread tips
Helix angle Rating Rating
T Thread top width (axial) ±1.3mm ±1.3mm
U Thread top (axial) groove width -- --
  1. For the B type, the maximum deviation of any thread height can exceed the allowable deviation specified in the table, but it should not exceed the allowable deviation of 0.08mm, and the average height of all threads should be in line with the given deviation range.
  2. The rating is based on the axis of the pipe.

jhkhh

hmkbkvm

dfgbdfsgsdb


製品グループ : シームレス鋼管

ホーム > 製品情報 > シームレス鋼管 > 高圧ボイラ用マルチリプルシームレス鋼管
この仕入先にメール
  • *タイトル:
  • *に:
    Mr. Richard SHEN
  • *イーメール:
  • *メッセージ:
    あなたのメッセージは20から8000文字の間でなければなりません
お問い合わせ
*
*

ホーム

Product

Whatsapp

私たちに関しては

お問い合わせ

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

送信